Propshaft length and dimesions of UJ

Post by: **bigvalvehead** » Wed Dec 02, 2015 1:19 pm

Hi
Does anyone have a 2 seat Elan propshaft out of the car so they can measure the length between the UJ's please.
Also diameter of the cups and distance to outsides of cross.

cheers
Dave

Post by: **patrics** » Wed Dec 02, 2015 7:07 pm

Hi Dave
Should be taking engine out over weekend if you can wait

Regards
Steve

Post by: **billwill** » Thu Dec 03, 2015 1:59 am

I put some propshaft photos in a topic long ago, but Alas I should have put a ruler in the picture.

lotus-parts-f33/diff-propshaft-timing-case-original-exhaust-header-t22669.html?hilit=propshaft

Post by: **gjz30075** » Thu Dec 03, 2015 9:55 am

billwill wrote:I put some propshaft photos in a topic long ago, but Alas I should have put a ruler in the picture.

lotus-parts-f33/diff-propshaft-timing-case-original-exhaust-header-t22669.html?hilit=propshaft

Perfect! What's the width of a brick? Might be different in UK vs US.

Post by: **nmauduit** » Thu Dec 03, 2015 10:54 am

Hi Dave,

in case it helps (metric I'm afraid, so give or take half a mm) here are some photos of mine, off a '68 s4se :

: 68 S4 4 speed driveshaft

: 68 S4 4 speed driveshaft length 570.5mm

: 68 S4 4 speed driveshaft Ujoint 68.5mm

: 68 S4 4 speed driveshaft flange 92mm

: 68 S4 4 speed driveshaft inner 57mm

Post by: **billwill** » Thu Dec 03, 2015 1:03 pm

gjz30075 wrote:
billwill wrote:I put some propshaft photos in a topic long ago, but Alas I should have put a ruler in the picture.

lotus-parts-f33/diff-propshaft-timing-case-original-exhaust-header-t22669.html?hilit=propshaft

Perfect! What's the width of a brick? Might be different in UK vs US.

Those bricks are 6.2 cm wide. Excluding the mortar between bricks and 21.3 cm long.

2.56 cm per inch. gives 2.34 inches by 8.32 inches long

Post by: **RichardHawkins** » Thu Dec 03, 2015 6:53 pm

Dave,

I have a prop shaft out of my 1968 S4. If mnauduit has not answered your questions I could take some measurements for you.

Richard Hawkins

Post by: **denicholls2** » Fri Dec 04, 2015 3:18 pm

gjz30075 wrote:Perfect! What's the width of a brick? Might be different in UK vs US.

Are those metric, english, or whitworth bricks?

Also, I believe in this orientation it's the brick height/depth that is in question.

I can offer that standard gauge railroad tracks have the same spacing on both sides of the pond, at a nice 4 feet 8 1/2 inches, or 1435 millimeters. Perhaps we should measure up a driveshaft or two in those.

Or, at MIT they favor Smoots...

https://en.wikipedia.org/wiki/Smoot

Sorry 'bout that, it's Friday...

Post by: **billwill** » Fri Dec 04, 2015 7:14 pm

denicholls2 wrote:
gjz30075 wrote:Perfect! What's the width of a brick? Might be different in UK vs US.

Are those metric, english, or whitworth bricks?

Dunno about that but they are genuwine ENGINEERING bricks.

Fired in the flames of hell to resist british winters outdoors. :mrgreen: