Elan drive shaft coupling PCD for S1

PostPost by: rgh0 » Mon Nov 03, 2008 9:07 am

The S1 Elan - at least the early ones had a different pitch circle diameter (PCD) for the donut coupling spider bolts from the later S2/S3/S4 cars.

I am having a discussion with a friend on what the difference was. The only reference I can find in in the Robinshaw and Ross book "The original Lotus Elan" which is a little vague but implies it was about 1/4 inch larger.

The later cars PCD was 95mm which implies the S1 PCD was around 100mm.

Does anyone have a early S1 with original drive shafts and have they ever measured the donut spider PCD ?

cheers
Rohan
User avatar
rgh0
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 8407
Joined: 22 Sep 2003

PostPost by: paddy » Mon Nov 03, 2008 10:48 am

Hi,

I have some I can measure tonight.

Paddy
1963 Elan S1
User avatar
paddy
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1036
Joined: 27 Oct 2008

PostPost by: 65 Lotus » Mon Nov 03, 2008 12:23 pm

The PCD of the early Elan's rotoflex coupling is 4 inches, which unfortunately doesn't give the proper preload using the current batch of manufactured rotoflex couplings, but as an engineer at the factory told me a few years ago, "You don't really have much of a choice, now do you?"
Scott In Ohio
26/3795
65 Lotus
Second Gear
Second Gear
 
Posts: 80
Joined: 24 May 2007

PostPost by: cocky » Mon Nov 03, 2008 1:04 pm

I'm just at the end of the process of converting my donuts to CVs. I had a problem when I put my S1 together years ago as I bought some heavy duty diff output shafts which had the later dimension so I had to mix the two sizes (late and early) when fitting the inner donuts (which made a difficult job even more difficult). I searched for an answer to the early PCD question but I couldn't find one. For the CV conversion I had to make adaptor plates with two different dimensions. I used the 96mm dimension for the late type diff output shaft. I found through a little bit of trial and error on the mill that 100.2mm fitted my early type spiders. I tried 100mm but it wasn't right. The mill was accurate as the 96mm drillings fitted the later type spiders perfectly.
Not sure when the change came about. I had a set of drive shafts from my 1967 +2 and they were the later dimension.
Hope this helps. I'll post the full story of the conversion when it is completed (hopefully later this week).
Cheers,
Chris
1964 S1 (Now sold)
cocky
New-tral
 
Posts: 9
Joined: 02 Jun 2008

PostPost by: Bill » Mon Nov 03, 2008 6:32 pm

The smaller dia. was on 26/0538 - late 63.

During the restro 11 years back I converted to the later larger size. I have a doner car - 65 S2. The front disk brake assembly was a smaller dia. than later cars as well, I also changed those to the larger dia disks and calipers. I suspect both changes were done simutaniously at the factory.

The origional factory shop manual does not address the change or differences in any way.

Bill
User avatar
Bill
Third Gear
Third Gear
 
Posts: 368
Joined: 05 Oct 2003

PostPost by: types26/36 » Mon Nov 03, 2008 9:20 pm

The S1 discs/shafts were fitted into the early S2 cars (S1.5) at least untill 26/3944 and a probably quite a few later.
Here is a pic of some new S1/S2 (early) disc's which I bought to fit to my early S2 although I also made up CV shafts to suit
Attachments
S1 AND EARLY S2 DISC.jpg and
Brian
64 S2 Roadster
72 Sprint FHC
User avatar
types26/36
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 3402
Joined: 11 Sep 2003

PostPost by: paddy » Mon Nov 03, 2008 11:32 pm

Hi,

Some measurements with a micrometer, centre-to-centre between holes in the spider:

"standard" (ie late) spider: 83.0 mm
early spider: 86.8 mm

PCD = centre-centre distance / sin(60) gives

standard: 95.84 mm
early: 100.23 mm

which matches the empirical 100.2 reported above and means it is *not* 4" (101.6 mm).

On the subject of preload and compatibility with later-type donuts, I had always assumed that in fact the nominal donut PCD didn't change, but the smaller diameter was adopted to increase the preload - but that's just a guess.

Paddy
1963 Elan S1
User avatar
paddy
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1036
Joined: 27 Oct 2008

PostPost by: rgh0 » Tue Nov 04, 2008 5:03 am

Thanks guys for the quick responses - It never ceases to amaze me that such an obscure question can be answered so quickly

My summary of the data is

late PCD 95.8 +/- 0.2mm
early PCD 100.2 +/- 0.2 mm

The tolerancing is my estimate from measuring up the 4 spare shafts and 4 spare disks I have plus the data given.

The change over from early to late was during the early S2 production and after chassis number 26 / 3944

cheers
Rohan
User avatar
rgh0
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 8407
Joined: 22 Sep 2003

PostPost by: jpt » Sun Dec 18, 2011 10:25 pm

In a recent post, Gary noted that the early PCD driveshafts were supplied for the first 1000 or so Elans, up to around 26/4027.
http://www.lotuselan.net/forums/elan-f14/rear-axle-t24218.html

I just measured the driveshafts that were on my Elan, 26/4203, when I bought it in 1981 and confirmed that they are the late (95.8 mm) ones, so this provides more definition about the changeover point.

Jon
jpt
New-tral
 
Posts: 14
Joined: 21 Oct 2009

PostPost by: garyeanderson » Sun Dec 18, 2011 11:01 pm

4027 is Peter's phone number, oops 4109 is the change point according to the Ross and Robinshaw book. Oh well, more misinformation as it becomes available :)

Gary
User avatar
garyeanderson
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2626
Joined: 12 Sep 2003

PostPost by: Bill » Mon Dec 19, 2011 2:25 am

Rohan

If I were to order a set of your driveshafts for 26/0538 (late 63 production) which I intend to do in the near future, and considering the fact that I may have installed later shafts from my doner car during the last rebuild many years ago which made it work ay the time - I assume that you will need the PCD measurements to confirm correct supply. It has been so long that I am not sure of the spider size except that I changed the shafts to my S2 spares.

I will be lifting it thu the winter (new MaxJax 2 post) for maintenance and can check it out.

Bill
Bill Rathlef
Vancouver Island, Canada
"Keep your stick on the ice, boys."
User avatar
Bill
Third Gear
Third Gear
 
Posts: 368
Joined: 05 Oct 2003

PostPost by: bob_rich » Tue Feb 14, 2012 9:10 pm

Hi Rohan

Looks like you have enough info but I did a scan on a 5mm square grid on the disc of my car
+2 Dec 1973 +2S130. Hope it helps and not adds 2 confusion!!

cheers

Bob
Attachments
rear_disk_+2S130.jpg and
bob_rich
Fourth Gear
Fourth Gear
 
Posts: 555
Joined: 06 Aug 2009

Total Online:

Users browsing this forum: No registered users and 23 guests