Clutch slave cylinder

PostPost by: peterlotuselan » Fri Mar 15, 2019 11:30 am

Help, I recently rebuilt my engine, and replaced the bell housing, now I find the hydraulic elbow coming out of the slave cylinder is touching the exhaust manifold, has anybody had such an issue and how did you solve? Is there a shorter elbow one can get to fit into the slave cylinder?
peterlotuselan
New-tral
 
Posts: 11
Joined: 03 Jun 2016

PostPost by: elansprint71 » Fri Mar 15, 2019 3:23 pm

Have you got an issue with your engine mounts? Or has something else changed.


Shouldn't be a problem with getting an elbow and fittings from somewhere like Burton Power.
User avatar
elansprint71
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2624
Joined: 16 Sep 2003

PostPost by: peterlotuselan » Fri Mar 15, 2019 6:33 pm

Thanks for the suggestion I will have a look at the engine mounts to see if maybe that is the case.
peterlotuselan
New-tral
 
Posts: 11
Joined: 03 Jun 2016

PostPost by: oldelanman » Fri Mar 15, 2019 6:49 pm

What pipe and fittings do you have ?
I changed to a one piece braided stainless hose and had a similar issue - it was too close to the exhaust although not actually touching. I improved the clearance by shortening the fitting into the slave cylinder and using a copper washer to seal instead of the taper seat.
clutch-pipe-routing-003.jpg and
clutch-slave-002.jpg and
Roger
S4 DHC
oldelanman
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1927
Joined: 02 Jan 2008

PostPost by: SENC » Fri Mar 15, 2019 11:51 pm

You could change to a banjo connection, though I agree it shouldn't be close now than before unless something else changed.
Henry
69 Elan S4
65 Seven S2
SENC
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1030
Joined: 30 Dec 2015

PostPost by: Famous Frank » Sat Mar 16, 2019 4:52 am

Roger,

Nice installation! Very nice indeed!

Frank
Famous Frank

67 Elan Coupe
66 Elan S2 SE
65 Elan S2
65 Elan 26R
69 S2 Europa
06 Elise
67 Barracuda
User avatar
Famous Frank
Fourth Gear
Fourth Gear
 
Posts: 556
Joined: 29 Apr 2004

PostPost by: oldelanman » Sat Mar 16, 2019 10:15 am

Thanks Frank.
Roger
S4 DHC
oldelanman
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1927
Joined: 02 Jan 2008

PostPost by: peterlotuselan » Thu Apr 04, 2019 9:04 am

Thanks for the thoughts, I will take a picture to show but I think the idea of shortening the fitting into the slave cylinder is probably the way forward. I think I might also be able to move the slave cylinder back a bit as it is a bit slack in the bell housing section.

I will of course let you know the outcome but thanks again for the ideas, much appreciated.
peterlotuselan
New-tral
 
Posts: 11
Joined: 03 Jun 2016

PostPost by: Craven » Thu Apr 04, 2019 10:37 am

SENC wrote:You could change to a banjo connection, though I agree it shouldn't be close now than before unless something else changed.

By far the best and easy fix, parts are available so you can just change to banjo no need for new pipe and can be done in situ if needed.
Craven
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1623
Joined: 14 Sep 2013

PostPost by: JonB » Fri Apr 05, 2019 8:35 am

Quick question about the banjo fitting - is it supposed to seal against the body of the cylinder with a copper washer and if so, don't you need to ensure the cylinder body is flat (no dings or scratches)?
User avatar
JonB
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2371
Joined: 14 Nov 2017

PostPost by: Craven » Fri Apr 05, 2019 11:04 am

Yes, but no problem with sealing of the copper washer, you could swop over to the bleed nipple hole as this has a machined surface.
With a slight modification to the sandwich plate the cylinder can be rotated to put the bleed nipple to the highest point of the cylinder.
slave.jpg and
Craven
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1623
Joined: 14 Sep 2013

Total Online:

Users browsing this forum: No registered users and 21 guests