Tandem master disassembly?

PostPost by: The Veg » Tue Oct 25, 2016 11:39 pm

What's the trick to getting the piston assembly out of a Girling tandem mater cylinder?
1970 Elan Plus 2 (not S) 50/2036
2012 BMW R1200GS
"It just wouldn't be a complete day if I didn't forget something!" -Me
User avatar
The Veg
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2191
Joined: 16 Nov 2015

PostPost by: lotocone » Wed Oct 26, 2016 12:50 am

Working from memory, I think that once the reservoir is out there is a large Allen fitting that needs to be removed.
It is so big that I had to buy the Allen wrench. It might be about 1/2 in. I wish I had a manual to refer to, but it's not available right now. Hope this helps.
Bob
1969 S4
lotocone
Third Gear
Third Gear
 
Posts: 238
Joined: 09 Feb 2010

PostPost by: The Veg » Wed Oct 26, 2016 1:13 am

Thanks Bob; I did see that fitting but didn't put 2+2 together that it would be in the way. Will have a go at it.
1970 Elan Plus 2 (not S) 50/2036
2012 BMW R1200GS
"It just wouldn't be a complete day if I didn't forget something!" -Me
User avatar
The Veg
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2191
Joined: 16 Nov 2015

PostPost by: tedtaylor » Wed Oct 26, 2016 1:25 am

do NOT fully remove the reservoir, only swing it off to the side !!!!
TED
"Driving a Lotus is a triumph of bravery over intelligence." Stirling Moss
"TaylorMadeClassicCars" on WWW and Facebook
tedtaylor
Fourth Gear
Fourth Gear
 
Posts: 550
Joined: 09 Dec 2012

PostPost by: lotocone » Wed Oct 26, 2016 2:13 am

The Veg wrote:Thanks Bob; I did see that fitting but didn't put 2+2 together that it would be in the way. Will have a go at it.


You're welcome sir. I hope the rebuild goes well.

In my case, I got the master cylinder sleeved with brass, but I guess it's not necessary unless there is bad scoring. The place I used closed due to retirement of the owner, or I'd recommend them.

Bob
Bob
1969 S4
lotocone
Third Gear
Third Gear
 
Posts: 238
Joined: 09 Feb 2010

PostPost by: 1owner69Elan » Wed Oct 26, 2016 7:15 am

I went through my tandem MC rebuild a few months back and got help on the forum.

See this thread:

lotus-suspension-f42/elan-federal-brake-master-cylinder-t36306.html?hilit=Master#p248875
'69 Elan S4 SE
Street 181 BHP
Original owner
1owner69Elan
Fourth Gear
Fourth Gear
 
Posts: 846
Joined: 16 Jun 2015

PostPost by: Lotusdavid » Wed Oct 26, 2016 1:27 pm

If all else fails, I have a NOS tandem for sale!
Lotusdavid
First Gear
First Gear
 
Posts: 21
Joined: 21 Mar 2016

PostPost by: The Veg » Fri Oct 28, 2016 11:28 pm

Update: got the big hexy thing out and with some doing, the piston nearest the pushrod came out along with a lot of sludgy black stuff that I presume was once the seal. The other piston is stuck way back in the bore at the moment, and the bore is well-coated with hard brown brake fluid residue crust, and I presume that this stuff is what's holding the other piston in place. Anybody have a favourite method for dissolving the crust?
1970 Elan Plus 2 (not S) 50/2036
2012 BMW R1200GS
"It just wouldn't be a complete day if I didn't forget something!" -Me
User avatar
The Veg
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2191
Joined: 16 Nov 2015

PostPost by: nmauduit » Sat Oct 29, 2016 9:33 am

The Veg wrote:Update: got the big hexy thing out and with some doing, the piston nearest the pushrod came out along with a lot of sludgy black stuff that I presume was once the seal. The other piston is stuck way back in the bore at the moment, and the bore is well-coated with hard brown brake fluid residue crust, and I presume that this stuff is what's holding the other piston in place. Anybody have a favourite method for dissolving the crust?


unless it has cooked solid, compressed air at the return valve port (where the MC tends to leak...) should push the slave piston out. You may want a piece of cloth to gather small parts before they get airborne...
S4SE 36/8198
User avatar
nmauduit
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2006
Joined: 02 Sep 2013

PostPost by: The Veg » Tue Nov 01, 2016 3:22 am

Yes, the air did get the piston out, but the question remains: what's the best stuff for dissolving the brown crust of fluid residue? So far I've had poor results with penetrating oil and with mineral spirits.
1970 Elan Plus 2 (not S) 50/2036
2012 BMW R1200GS
"It just wouldn't be a complete day if I didn't forget something!" -Me
User avatar
The Veg
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2191
Joined: 16 Nov 2015

PostPost by: nmauduit » Tue Nov 01, 2016 10:56 am

The Veg wrote:Yes, the air did get the piston out, but the question remains: what's the best stuff for dissolving the brown crust of fluid residue? So far I've had poor results with penetrating oil and with mineral spirits.


I don't recall how bad it was on mine when I cleaned it up, but I spent some time fine wet sanding with the mineral oil to smooth out the color changes. The way I did it was rolling a new sheet of fine (1000) paper all the way inside the bore and unrolling it inside to do the smoothing, so that remaining lines would not be long the axis (direction of leaks) - that repeated a number of time with cleaning in between. I did not clean it up 100%, just to the point it looked smooth under close scrutiny with a led (a bit like gun bore inspection) and the discoloration (oxidation spots) seemed small enough and not located where the pressure would occur (e.g. in front of the master piston, rod side). I have then switched the system to silicone (DOT 5.0) to avoid internal oxidation from absorbed moisture.

So far this has worked for me... but I don't know if the smoothness level achieved will lead to more frequent rebuilding.
S4SE 36/8198
User avatar
nmauduit
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2006
Joined: 02 Sep 2013

Total Online:

Users browsing this forum: No registered users and 16 guests