Front brake cooling

PostPost by: john.p.clegg » Fri Oct 10, 2014 4:05 pm

Me again
Just have a little time on my hands and was wondering about extra cooling for the front brakes on the plus2...any experience.....any comments....any ideas...anyone done it....any photos.

Will it be the calipers or the discs that need the "extra air-flow" or both???

John :wink:
User avatar
john.p.clegg
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 4521
Joined: 21 Sep 2003

PostPost by: rgh0 » Sat Oct 25, 2014 9:25 am

Take off the brake back plate and mount the duct tp feed air into the general area of the brake and calliper. It does not matter much were you put the air versus just the right and best place to run the duct I think.

The S4 Seven my friend runs has much cooler brakes its lighter weight will help but having the wheels and brakes in the open I am sure helps a large amount so just getting a better air flow into the area will help

cheers
Rohan
User avatar
rgh0
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 8407
Joined: 22 Sep 2003

PostPost by: alan.barker » Fri Oct 31, 2014 7:04 pm

john.p.clegg wrote:Me again
Just have a little time on my hands and was wondering about extra cooling for the front brakes on the plus2...any experience.....any comments....any ideas...anyone done it....any photos.

Will it be the calipers or the discs that need the "extra air-flow" or both???

John :wink:

why extra cooling are you only doing trackdays :?:
Alan.b Brittany 1972 elan sprint fhc Lagoon Blue 0460E
alan.barker
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 3762
Joined: 06 Dec 2008

PostPost by: john.p.clegg » Sat Nov 01, 2014 7:29 am

no,just too much time on my hands..

John :wink:
User avatar
john.p.clegg
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 4521
Joined: 21 Sep 2003

PostPost by: Spyder fan » Sat Nov 01, 2014 8:55 am

Cross drilled and grooved discs help with fade / cooling issues, Kelvedon show them on their website http://www.kelsport.net/parts/products. ... ectionID=2

Updated calipers are available as well, all this stuff is okay for a road car doing occasional track days, probably not acceptable for race cars as most formulas have strict rules on brakes.
Kindest regards

Alan Thomas
User avatar
Spyder fan
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2022
Joined: 11 Jun 2009

PostPost by: elansprint71 » Tue Nov 11, 2014 1:09 pm

Cleggy,
Don't forget that if you do remove the back-plate and drive in the rain (normal round our way, innit?) that your front brakes will not work for the first few yards, so make allowances! Don't ask me how I know. :(

I imagine that this situation will never arise in a race, unless you are at Le Mans or maybe Bathurst, because you'll be braking frequently. :twisted:
User avatar
elansprint71
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2624
Joined: 16 Sep 2003

PostPost by: Andy8421 » Mon Jan 26, 2015 8:10 am

If you do remove the backplate and track the car, you will cook the rubber on the end of the steering arm balljoint with heat radiated from the disc. I believe the 26R had steering rod ends with metal covers rather that the usual rubber to avoid this problem.
68 Elan S3 HSCC Roadsports spec
71 Elan Sprint (still being restored)
32 Standard 12
Various modern stuff
Andy8421
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1234
Joined: 27 Mar 2011

PostPost by: oldchieft » Mon Jan 26, 2015 11:29 am

Morgans never had back plates and i never heard of any wet weather or heat problems.

Jon the Chief
oldchieft
Third Gear
Third Gear
 
Posts: 374
Joined: 17 Sep 2013

PostPost by: rgh0 » Mon Jan 26, 2015 12:49 pm

I melted / burnt the rubber seals on the tie rod ends on my Elan on the track a few years ago. But the brakes are getting much much hotter than they ever would on the road. The last set I put on seem to have seals of a different material and they have not melted or shown any problems from heat from the disks

cheers
Rohan
User avatar
rgh0
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 8407
Joined: 22 Sep 2003

PostPost by: TroonSprint » Mon Jan 26, 2015 1:41 pm

Don't forget that if you do remove the back-plate and drive in the rain (normal round our way, innit?) that your front brakes will not work for the first few yards, so make allowances!

My MGB V8 with uprated brakes has no back plates on the discs. I have driven it over 20,000 miles in rain, ice and snow (I live in Scotland!) and have never had a problem with the brakes not working properly because of water on the disc. I'm not saying it can't happen, but It has never happened to me.

Mike
User avatar
TroonSprint
Fourth Gear
Fourth Gear
 
Posts: 507
Joined: 24 Nov 2011

PostPost by: nmauduit » Mon Sep 18, 2017 6:33 am

here is what I did for the occasional track day run :

air-duct-welded-on.jpg and
air duct welded to dust shield


p1040525.jpg and
fresh air from below the radiator


p1040530.jpg and
steering locked to the left


p1040531.jpg and
steering locked to the right
S4SE 36/8198
User avatar
nmauduit
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2006
Joined: 02 Sep 2013

PostPost by: john.p.clegg » Thu Sep 21, 2017 7:42 pm

COOL , as they say these days...

John :wink:
User avatar
john.p.clegg
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 4521
Joined: 21 Sep 2003

PostPost by: Bigbaldybloke » Sun Nov 26, 2017 1:29 am

On a similar vein, has anyone fitted ventilated front discs on their road going plus 2 and if so what and how have they done it. I?ve seen kits to widen the Girling type 16 calipers to accommodate the wider ventilated discs and I?ve also found kits intended for Triumph GT6/Vitesse/TR to fit complete replacement alloy calipers and ventilated discs but not sure if they are compatible with Lotus knock on wheels?
Change is inevitable, except from a vending machine!
Bigbaldybloke
Fourth Gear
Fourth Gear
 
Posts: 889
Joined: 16 May 2017

PostPost by: Foxie » Sun Nov 26, 2017 2:48 am

Bigbaldybloke wrote:On a similar vein, has anyone fitted ventilated front discs on their road going plus 2 and if so what and how have they done it.


I converted to full set of Sierra hubs with vented front discs from Spyder Zetec. Expensive, as I had to order modded drive shafts and change the wheels to suit, but absolutely no problem brakes now on circuit racing :)

(I kept the Lotus h/brake system, just modded the tree to match the Sierra h/brake height)
68 Elan +2, 70 Elan +2s
User avatar
Foxie
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1210
Joined: 20 Sep 2003

PostPost by: Bigbaldybloke » Mon Nov 27, 2017 9:56 pm

I wanted to keep knock on wheels rather than change hubs uprights etc. Ventilated discs fitted to existing uprights with modified type 16 calipers seems the simplest way to get brakes with better cooling, just need to work out the right combination of parts and what if any machining is required to get it all working.
Change is inevitable, except from a vending machine!
Bigbaldybloke
Fourth Gear
Fourth Gear
 
Posts: 889
Joined: 16 May 2017
Next

Total Online:

Users browsing this forum: No registered users and 18 guests