Plus 2 sill moulding fitting
9 posts
• Page 1 of 1
Post by: TonyA » Wed Mar 22, 2023 3:26 pm
I had successfully removed my dented sill moulding ( the one below the door) basically by pressing from above, and unclipping it from the bottom, clip by clip. The old adage that replacement is the reverse seems not to be applying and I don't want to damage anything. Any advice/tips/ tools on how to fit the new moulding back on the clips (which are the original riveted 'J' profile type, ..Thx..Tony
PS I got the new mouldings from SJ Sportscars if anyone interested. They are high quality (non magnetic) stainless.
PS I got the new mouldings from SJ Sportscars if anyone interested. They are high quality (non magnetic) stainless.
- TonyA
- Second Gear
- Posts: 176
- Joined: 04 Jan 2022
Post by: alan.barker » Wed Mar 22, 2023 4:04 pm
Don't forget the rubber bungs for each end.
Maybe new trim is narrower. Easy to make clips from stainless.
Alan
Maybe new trim is narrower. Easy to make clips from stainless.
Alan
Alan.b Brittany 1972 elan sprint fhc Lagoon Blue 0460E
- alan.barker
- Coveted Fifth Gear
- Posts: 3754
- Joined: 06 Dec 2008
Post by: Gazzerb » Wed Mar 22, 2023 7:52 pm
Alan
On my original cill strips, the 'bung' is just a small strip of black neoprene foam about 5/16" wide glued to the back of the strip and trimmed off flush with the ends.
Attached sketch from my notes should clarify.
Gary
On my original cill strips, the 'bung' is just a small strip of black neoprene foam about 5/16" wide glued to the back of the strip and trimmed off flush with the ends.
Attached sketch from my notes should clarify.
Gary
- Attachments
-
Plus 2 Cill Strips.pdf- (124.51 KiB) Downloaded 193 times
Gary
1972 Elan +2 S130/5
2001 Elise S2
1972 Elan +2 S130/5
2001 Elise S2
- Gazzerb
- Second Gear
- Posts: 62
- Joined: 21 Apr 2005
Post by: alanr » Wed Mar 22, 2023 8:51 pm
Thanks.. 
However the original ones I have in my memory from back in the day ,which admittedly could be completely wrong, are more of a hard rubber/plastic material with a recess that pushed part way into the strip.
Alan.
However the original ones I have in my memory from back in the day ,which admittedly could be completely wrong, are more of a hard rubber/plastic material with a recess that pushed part way into the strip.
Alan.
Alan
'71 +2 S130/ 5speed Type9.
'71 +2 S130/ 5speed Type9.
- alanr
- Coveted Fifth Gear
- Posts: 1027
- Joined: 14 Sep 2018
Post by: mbell » Wed Mar 22, 2023 11:40 pm
Hook it over the angled part of the clips, push other edge against curved part. If it won't push on then try gentle taps with a rubber mallet or similar?
Just need to get it to "pop" over the clip.
Just need to get it to "pop" over the clip.
'73 +2 130/5 RHD, now on the road and very slowly rolling though a "restoration"
- mbell
- Coveted Fifth Gear
- Posts: 2643
- Joined: 07 Jun 2013
Post by: 3261R » Thu Mar 23, 2023 1:19 am
Just did mine with new stainless clips and new trimpiece.
Found the easiest way was to hook it over the top of the clip then give it a smart thump at a downward angle with the heel of my hand. Hand was a bit sore after doing both sides!
The end profile of the trim is not symmetrical - I hooked the smaller edge over the top.
Found the easiest way was to hook it over the top of the clip then give it a smart thump at a downward angle with the heel of my hand. Hand was a bit sore after doing both sides!
The end profile of the trim is not symmetrical - I hooked the smaller edge over the top.
- 3261R
- New-tral
- Posts: 11
- Joined: 06 Nov 2020
9 posts
• Page 1 of 1
Total Online:
Users browsing this forum: No registered users and 35 guests
Site map
SitemapIndex
RSS Feed