Lock Nuts for Front Suspension

Post by: **Mr.Gale** » Thu Oct 24, 2013 4:55 pm

Where in the US can I buy new low profile lock nuts? The studs that the A-arms pivot on are not very long and the lock nuts that I can buy locally are too tall (see photo).

Thanks,
Gale

Post by: **RotoFlexible** » Thu Oct 24, 2013 5:32 pm

I believe R.D. Enterprises carried them, but I don't see them on the website any more. I think I bought a set of them, but they stripped pretty easily.

McMaster-Carr is a good bet: http://www.mcmaster.com/#hex-locknuts/=p2stks

Post by: **collins_dan** » Thu Oct 24, 2013 5:57 pm

Ray has half nuts, which work fine. They leave room for a washer.
Dan

Hmmm.... maybe I should re-word that so as not to offend Ray. :shock:

Ray stocks half nuts, which work fine.

Post by: **elansprint** » Thu Oct 24, 2013 6:00 pm

I think they are referred to as P type in the UK the lower Nylocks think they are 1/2 inch UNF from memory
Ian

Post by: **Bud English** » Thu Oct 24, 2013 7:25 pm

I got mine from McMaster Carr. Their part number 94945A225, $6.47 for 5. Grade 8, 1/2-20.

: Half nut.jpg (44.65 KiB) Viewed 1530 times

Leaves plenty of room for an SAE washer.
(Please disregard the dust. There's body work going on in the background.)

Post by: **StressCraxx** » Thu Oct 24, 2013 8:53 pm

Mr.Gale wrote:Where in the US can I buy new low profile lock nuts? The studs that the A-arms pivot on are not very long and the lock nuts that I can buy locally are too tall (see photo).
Thanks,
Gale

Aircraft spruce and specialty
Aircraftspruce.com

Coast fabrication
Coastfab.com

Post by: **ensign42** » Fri Oct 25, 2013 12:06 am

I have yet to find a piece of hardware that Fastenal could not supply. I have used them for big marine applications and AC&R work for years. Great products, and good counter service. They are a bit more expensive than McMaster but in my experience they have always been worth it.

Will

Post by: **StressCraxx** » Fri Oct 25, 2013 2:43 am

Agree that Fastenal is great. I had forgot about them.

Their branches are located in most cities, usually in industrial areas they serve.

Post by: **reb53** » Fri Oct 25, 2013 5:05 am

You need a friend with a lathe.....

Ralph.

Post by: **Galwaylotus** » Fri Oct 25, 2013 8:54 am

reb53 wrote:You need a friend with a lathe.....

Ralph.

. . . or a bench grinder!

Post by: **Bud English** » Fri Oct 25, 2013 4:43 pm

...for ten bucks?

Post by: **pamitchell** » Mon Oct 28, 2013 1:35 am

Hi Gale

Also check w. Olander Co. in Sunnyvale.

Post by: **Bud English** » Mon Oct 28, 2013 4:03 am

I don't know for sure if they have these nuts but another source for mil-spec hardware here in the states is the Bon Aero division of Dave Bean. The link is at the bottom of their main page.

http://www.davebean.com/

Post by: **gearbox** » Mon Oct 28, 2013 5:09 am

+1 on McMaster Carr, pretty much sourced all the bolts and fasteners I needed on my S4 rebuild. Plus if you put the order in early enough, you get it the next day, The only problem I have is always forgetting something I should have ordered after pressing the confirm button lol.

Post by: **Grizzly** » Sat Aug 20, 2016 1:48 pm

Just going through old Threads looking for some thing else but just seen this one.

I had a problem with the right Nuts too but a friend owns a Triumph Motorbike main dealer, he told me those 1/2 Unf T-Type nuts are commonly used on old Triumph motorbikes and are easy to get through Classic bike specialists.

These are the ones he supplied me (Centre) the Original one is Grey (right) and the last is a full nut (Left) for comparison.

The big washer that goes behind that nut is 1/2x1.25"

Lock Nuts for Front Suspension

Total Online:

Recent Forum Topics

Support LotusElan.net!

Recent Wiki Articles