Easy weber mixture tool
35 posts
• Page 2 of 3 • 1, 2, 3
twincamman wrote:Oiiiiiii....runners make headers ...that run into 4 into 2 into 1 collectors and that runs into the exhaust tube ........and that's attached to the rib bone....this causing me exhaustivity
It's hard work on 'ere 'innit Ed
Beware of the Illuminati
Editor: On Sunday morning, February 8th 2015, Derek "John" Pelly AKA GrumpyBodger passed away genuinely peacefully at Weston Hospicecare, Weston Super Mare. He will be missed.
Editor: On Sunday morning, February 8th 2015, Derek "John" Pelly AKA GrumpyBodger passed away genuinely peacefully at Weston Hospicecare, Weston Super Mare. He will be missed.
-
GrUmPyBoDgEr - Coveted Fifth Gear
- Posts: 3062
- Joined: 29 Oct 2004
All around 460 F.....try to make them as close as you can...... around the bend
dont close your eyes --you will miss the crash
Editor: On June 12, 2020, Edward Law, AKA TwinCamMan, passed away; his obituary can be read at https://www.friscolanti.com/obituary/edward-law. He will be missed.
Editor: On June 12, 2020, Edward Law, AKA TwinCamMan, passed away; his obituary can be read at https://www.friscolanti.com/obituary/edward-law. He will be missed.
-
twincamman - Coveted Fifth Gear
- Posts: 3175
- Joined: 02 Oct 2003
]
Is "runner" Canadian for what USA people call "headers" and UK people call "Exhaust Manifold" ?[/quote]
And Australians call "extractors"
Is "runner" Canadian for what USA people call "headers" and UK people call "Exhaust Manifold" ?[/quote]
And Australians call "extractors"
- AussieJohn
- Third Gear
- Posts: 456
- Joined: 10 Jun 2007
Cheers,
Pete.
http://www.petetaylor.org.uk
LOTUS ELAN flickr GROUP: https://www.flickr.com/groups/2515899@N20
flickr: http://www.flickr.com/photos/16096573@N02/sets/72157624226380576/
https://www.flickr.com/photos/16096573@N02/
Pete.
http://www.petetaylor.org.uk
LOTUS ELAN flickr GROUP: https://www.flickr.com/groups/2515899@N20
flickr: http://www.flickr.com/photos/16096573@N02/sets/72157624226380576/
https://www.flickr.com/photos/16096573@N02/
-
elansprint71 - Coveted Fifth Gear
- Posts: 4437
- Joined: 16 Sep 2003
No there are 4 runners to a manifold (5 if you drive an Audi or 8 if you drive a chebby)
dont close your eyes --you will miss the crash
Editor: On June 12, 2020, Edward Law, AKA TwinCamMan, passed away; his obituary can be read at https://www.friscolanti.com/obituary/edward-law. He will be missed.
Editor: On June 12, 2020, Edward Law, AKA TwinCamMan, passed away; his obituary can be read at https://www.friscolanti.com/obituary/edward-law. He will be missed.
-
twincamman - Coveted Fifth Gear
- Posts: 3175
- Joined: 02 Oct 2003
Ok. Serious for a moment A cold engine at idle after a 2 minute. Idle was 438 degrees ....across the runners ..headers .. Collectors.. pipes ...round things bolted to the head exhaust thingies
dont close your eyes --you will miss the crash
Editor: On June 12, 2020, Edward Law, AKA TwinCamMan, passed away; his obituary can be read at https://www.friscolanti.com/obituary/edward-law. He will be missed.
Editor: On June 12, 2020, Edward Law, AKA TwinCamMan, passed away; his obituary can be read at https://www.friscolanti.com/obituary/edward-law. He will be missed.
-
twincamman - Coveted Fifth Gear
- Posts: 3175
- Joined: 02 Oct 2003
Ed,
Thanks for the approximate target temp. info: at about what distance from the head/manifold flange do you measure, I tried this before some time ago and found the temp. drop vs dist. significant, rather logically as Spok would say. Is about two inches correct, before one gets into additional metal affecting heat dissipation and since runers join at diff. places need to not get too close to that). If too close to the head does the head cooling affect it? I have stainless headers, not stock cast ones.
Jack
ps: fellow canuck, understood the lingo ))).
Note,
Just reread, you said "around the bend... "
Thanks for the approximate target temp. info: at about what distance from the head/manifold flange do you measure, I tried this before some time ago and found the temp. drop vs dist. significant, rather logically as Spok would say. Is about two inches correct, before one gets into additional metal affecting heat dissipation and since runers join at diff. places need to not get too close to that). If too close to the head does the head cooling affect it? I have stainless headers, not stock cast ones.
Jack
ps: fellow canuck, understood the lingo ))).
Note,
Just reread, you said "around the bend... "
- jk952
- Third Gear
- Posts: 304
- Joined: 04 Jan 2011
As long as your distance is the same for all readings it is irrelivent ...I stand and aim .....like the urinal ....Temperature is temperature?..and around the bend is where these guys are sending me aaAAAAAAAAAAaA....
dont close your eyes --you will miss the crash
Editor: On June 12, 2020, Edward Law, AKA TwinCamMan, passed away; his obituary can be read at https://www.friscolanti.com/obituary/edward-law. He will be missed.
Editor: On June 12, 2020, Edward Law, AKA TwinCamMan, passed away; his obituary can be read at https://www.friscolanti.com/obituary/edward-law. He will be missed.
-
twincamman - Coveted Fifth Gear
- Posts: 3175
- Joined: 02 Oct 2003
weLL i threw the ball through the window and it was light enough to hit the llight ..Idont envy any one whos mother language isnt ENglish.....
dont close your eyes --you will miss the crash
Editor: On June 12, 2020, Edward Law, AKA TwinCamMan, passed away; his obituary can be read at https://www.friscolanti.com/obituary/edward-law. He will be missed.
Editor: On June 12, 2020, Edward Law, AKA TwinCamMan, passed away; his obituary can be read at https://www.friscolanti.com/obituary/edward-law. He will be missed.
-
twincamman - Coveted Fifth Gear
- Posts: 3175
- Joined: 02 Oct 2003
35 posts
• Page 2 of 3 • 1, 2, 3
Total Online:
Users browsing this forum: No registered users and 20 guests