Fitting bumpers
10 posts
• Page 1 of 1
Last time I simply bolted them on and used a rubber penny washer between the bumper and the body and a stainless penny washer on the back side
But SJ Sportscars show a thick rubber buffer for bumper mounting - is this necessary and where does it go?
Any other tips - was thinking of put a self adhesive foam strip between the bumper and body just to isolate it.
But SJ Sportscars show a thick rubber buffer for bumper mounting - is this necessary and where does it go?
Any other tips - was thinking of put a self adhesive foam strip between the bumper and body just to isolate it.
- jono
- Coveted Fifth Gear
- Posts: 2052
- Joined: 17 May 2007
Hello jono, just refitted the front bumper on my +2 and put the rubber back from whence it came from.it sits sandwiched between the body and the underneath of the bumper so there is a gap all around.I used stainless penny washers under the nut to spread the load.The rubbers I removed we’re still good after 50 years not sure foam will stay the course.
72 Elan +2S 130/5
- Steve Brooks
- Second Gear
- Posts: 64
- Joined: 08 Oct 2014
hi Jono,
could you tell us the part number of the rubber buffer please. I don't suppose you've mistaken them for the rubber buffer for Headlamp Stops or For the rear of the Boot Lid.
Alan
could you tell us the part number of the rubber buffer please. I don't suppose you've mistaken them for the rubber buffer for Headlamp Stops or For the rear of the Boot Lid.
Alan
Alan.b Brittany 1972 elan sprint fhc Lagoon Blue 0460E
- alan.barker
- Coveted Fifth Gear
- Posts: 3827
- Joined: 06 Dec 2008
Steve Brooks wrote:Hello jono, just refitted the front bumper on my +2 and put the rubber back from whence it came from.it sits sandwiched between the body and the underneath of the bumper so there is a gap all around.I used stainless penny washers under the nut to spread the load.The rubbers I removed we’re still good after 50 years not sure foam will stay the course.
Thanks Steve, good to know - I never even knew these existed!
- jono
- Coveted Fifth Gear
- Posts: 2052
- Joined: 17 May 2007
Hi Jono,
Just fit rubber washers. I've used rubber Tap Washers and just made the hole a bit bigger in the past. You need to put sealant around to number plate lights wires to stop flooding in the Boot.
Alan
Just fit rubber washers. I've used rubber Tap Washers and just made the hole a bit bigger in the past. You need to put sealant around to number plate lights wires to stop flooding in the Boot.
Alan
Alan.b Brittany 1972 elan sprint fhc Lagoon Blue 0460E
- alan.barker
- Coveted Fifth Gear
- Posts: 3827
- Joined: 06 Dec 2008
The washers on mine when removed were about 3mm (1/8”) but they’d been squashed in there for many years so might have been a bit thicker when new, but not much as they are quite hard. Mine were actually square so not sure if they were original.
Change is inevitable, except from a vending machine!
- Bigbaldybloke
- Fourth Gear
- Posts: 894
- Joined: 16 May 2017
I used short lengths of heater or fuel hose to mount the rear bumper on my +2. You can easily cut a thicker or thinner piece if you get the clearance wrong at first.
Dave Chapman.
Dave Chapman.
- david.g.chapman
- Fourth Gear
- Posts: 815
- Joined: 26 Nov 2003
10 posts
• Page 1 of 1
Total Online:
Users browsing this forum: No registered users and 16 guests