LotusElan.net Unified Search
Search results for: cv shafts in category "Racing"
5 results found containing all search terms. 60 results found containing some search terms.
5 pages of results.
Sorted by relevance / Sort by date
Hello, I am recommissioning an Elan +2 vintage race car, to be raced at a regional level. The motor (currently being rebuilt) will have about ...
... CV vs. U-Joint rear axle conversion Hello, I am recommissioning an Elan ... appear to be stock diff. output shafts, which need to be upgraded. ...
I have to believe that any of you all racing under FIA regulations have this figured out- SO..... What is the reliable set up to ...
... brilliant, it is just like the CV drive shaft thing, do it once ... do it right and you can almost forget about it, I now know that ...
Dear all I have an Elan S3 which I use for classic rallys. I use a Monit rally computer with GPS. Due to restrictions and ...
... tab washers I made up on the cv bolts. Surprisingly accurate, actually, ... a visible part of the rotating propeller shaft as alternative for the sensor with no ...
4. Con.rods : Racing by LotusElan.net [Racing]
I have a set of new GAF forged narrow journal con rods ( made for a turbo engine) wich I intend to use in a ...
... Quaiffe gear box internals and LSD, CV drive shafts and strengthened diff and axle ... shafts. cheers Rohan rgh0 The Wilcox 2.2l twinc is on my ultimate wish list ...
The spring rate of the chassis is lower than that of your suspension . You must have smooth tracks and love racing go carts cheers ...
... only 3 bolts on a 6 bolt CV jonit. The other three are replaced ... hub, pressed onto a tapered steel shaft, undergoing both heat and load variations ...
6. Gear Box Reliability : Racing by LotusElan.net [Racing]
Recently I have become aware of an ongoing problem with gearbox reliability in high HP racing situations due to a failure in one of my ...
... elastic distortion of the iron gear box case. This results in the hardened steel shaft fretting on the iron casing and the resultant wear means the press fit becomes ...
7. Bullet Box input shaft : Racing by LotusElan.net [Racing]
Hi, I have just purchased a genuine close ratio bullit box (helical gears), and just found out that the input shaft is for the early ...
... Bullet Box input shaft Hi, I have just purchased a genuine close ratio bullit box (helical gears), and just found out that the input shaft ...
I just found out (!) that my jackshaft has got its gear totally stript after abt. 50 min. of working....(!!!) Naturally, I suspect the HP/HC ...
... have run both bronze and steel pump gears on both cast iron and steel jack shafts for High pressure / high volume pumps with no wear problems over lots of ...
9. Gearbox oil leak : Racing by LotusElan.net [Racing]
I entered my third race meeting on Saturday at Donington and I am describing it as a successful failure! Managed 17 laps in qualifying, which ...
... possibilities. The seal could just be knackered from incorrect installation, maybe a prop shaft vibration has damaged the bush and the seal, or there's too much pressure ...
10. REAR STUB AXLE : Racing by LotusElan.net [Racing]
At a race last weekend I had the unpleasant experience of a left rear stub axle failing and thus becoming a 3 wheel Elan. The ...
... ' - a superb stress raiser! Has anyone else had this problem? The shafts have done about 20 races, and look as if they had good contact ...
I am about to begin reinforcing my frame heretofore stock) and am considering raising the final drive by 1/2 inch to reflect the fact that ...
... pointless. By lowering the ride height you would not increase the amount the drive shafts could deflect upwards, you are reducing the amount of travel in the suspension ...
12. Zetec In Baby Elan : Racing by LotusElan.net [Racing]
As a long term entertainment project to create a track day car I want to put the two litre Zetec in a S4 baby elan ...
... I think will be the TTR bits for the diff output and the solid drave shaft etc. Thanks Mike miked Hi Mike, sounds like you are on the ...
Anybody replace the 15" diameter wooden steering wheel with a modern day quick release wheel of the same size? What brand of wheel and release ...
... with nothing. Looks like I'll have to weld on the flange to the steering shaft cause there aren't any direct bolt-on ones to buy. My question is the ...
14. CV axles : Racing by LotusElan.net [Racing]
Rohan wrote in 2005: Assembly The 7/16 UNF bolts can work loose in the adapter plates which is why the Elan factory conversion uses captive ...
... CV axles Rohan wrote in 2005: Assembly The 7/16 UNF bolts can work loose in the adapter plates which is why the Elan factory conversion uses ...
What oil pressure do you guys look to make in dry sumped racing engines? By way of benchmark figure - Miles Wilkins reckoned in his ...
... - There's a fair amount of work you can do in the passages, jack shafts etc. type of drilling in the cranks is also a factor. In ...
Search took 0.127 seconds