LotusElan.net Unified Search
Search results for: cv shafts in category "Racing"
5 results found containing all search terms. 60 results found containing some search terms.
5 pages of results.
The cam end is drilled and tapped for a longer sprocket bolt. The longer bolt runs past the first bearing and holds this section of ...
... hole and radial groove to feed oil from the first cam bearing down the cam shaft to the other bearings regards Rohan rgh0 Thanks Rohan Petter Petter Hval rgh0 wrote ...
I finally have acquired a racing Elan again-25 years after racing 26-R5 and 15 years after selling my last racing Elan in pieces. The car ...
... Heim jointed rear suspension, rear sway bar, close ratio gears, splined drive shafts and a Detroit Locker (Groan..) . I am sure I will ...
Hi, First up apologies to all the die hard race heads in here for dirtying up this forum with a topic on drifting. I attended ...
... drifting to be honest) . I'm also guessing I might need uprated diff output shafts and mounts, a beefier clutch (standard one feels too progressive) . ...
Those were the good old days where marshalls wandered around on the inside of corners inches away from the track rather than hiding in concrete ...
... Spare `dry sump` engine, All dry sump equipment, Wishbones, Drive shafts, Radiator, Long / short range tanks, Alternative springs, Anti roll ...
Chaps, I have not yet got round to sorting out a manifold (I have bought a S/H one but it has yet to arrive) but ...
... Both aluminium and magnesium materials are allowed for bell housing, gearbox casing, tail shaft housing and differential housing. High-capacity aluminium radiators may be used as well as ...
36. Alternator Woes : Racing by LotusElan.net [Racing]
Well I've done two trackdays now and have managed to kill an alternator after both either that same day or the very next. Usually try ...
... centrifical forces. -Keith type26owner Keith I run a 3 inch pulley on the crank shaft and a Lucas 18 ACR alternator. The same as Lotus originally fitted to ...
37. 26R Wheel dimensions : Racing by LotusElan.net [Racing]
I thought I would try asking here in the racing section. Can somebody give me the dimensions of the centre part of the peg-drive 26R ...
... . No key way but the bore is cerated for grip to the tapered steering shaft. I think this wheel may be from a 26R - just part of ...
38. Oil for dog box : Racing by LotusElan.net [Racing]
Hello All, About to install a newly built gearbox with a brand new quaife dog engagement gearset. The builder has recommended a 75/90 GL4 spec ...
... you would have burnt up any oil. Why your first gear seized on the shaft is an interesting question but it is highly unlikely it was due to an ...
G'day Rohan I had a long chat with Rob Wainwright who rebuilt this S1 R 22 for owner David Garrett. The body is apparently the ...
... Both aluminium and magnesium materials are allowed for bell housing, gearbox casing, tail shaft housing and differential housing. High-capacity aluminium radiators may be used as well as ...
Andrew Any idea what diff ratio he is using? Dave
... diameter..Personnaly the best ever top speed we reached with new tyre and a fresh 170 cv engine (dyno tested) .. is 198km/h .... Roger redcarandco ...
41. IWR Elans : Racing by LotusElan.net [Racing]
As the BRM's converted Elans have a thread, thought it worth putting one up for the IWR converted road cars. I'd be interested in seeing ...
... was pure 26R and was fitted with all the optional extras, including solid drive shafts, limited slip differential, strengthened chassis, adjustable suspension front and rear and ...
After making the podium in 2nd and 3rd places over the last four years, I finally took 1st place in the Irish National Hillclimb Championship ...
... ) are Zetec (Sierra) . Spyder made up special (CVJ) drive shafts to mate the original diff with the Zetec brakes. Wheels are 14" ...
43. Cosworth Elan : Racing by LotusElan.net [Racing]
Have just located,purchased and collected S3 FHC been stood 20 years,got it home spotted cosworth engine on floor wanting new home.Spent all night mentaly working ...
... holds record there ], 10" wide rear slicks, pds made asymetric drive shafts, 9" wide fronts, March 761 front uprights and Ralt F3 rear ...
44. Creating GTS style car from a S2 - the restoration begins : Racing - Page 3 by LotusElan.net [Racing]
Nice wheels David...they are also very similar to the 26r ones and you basically get 2 for the price of one !
... still. So, start with full race TT 26R chassis and suspension and drive shafts, a 4.4 lsd diff and you will go round the corners as fast ...
45. Lightweight flywheel : Racing by LotusElan.net [Racing]
I need to change the clutch. Whilst changing the clutch I might as well replace the old standard heavy flywheel. Can I put a new ...
... to 33.4 sec, so the rotational inertia is the predominate factor. The drive shaft and wheels/tires/brakes have an effect also, but they are ...
Search took 0.176 seconds