engine removal help
4 posts
• Page 1 of 1
Of course, the project is progressing much slower than expected but I
am finally ready to pull the engine out of my '70 Plus 2. I have never
done this before so I am looking for some basic guidence. Here what I
have done so far - removed everything that needs to be removed except:
1. the clutch slave cylinder. Somehow, it's just fused to the clutch
housing. The circlip is off but it won't budge nor rotate. Even the
air hammer and chisel won't budge it. So I figure, since I am pulling
the engine only (leaving the transmission in place), I really don't
need to remove the clutch slave cylinder at this time. Is that correct
2. haven't separated the engine from the transmission since I assume I
need to support the engine before I do that.
Can I remove the engine on my own or do I need an assistant?
I have a cherry picker and a load balancer. I am wondering where to
screw the load balancer into the engine to attach it. I have heard of
people hanging a sling off the load balancer; is that a better way to go?
am finally ready to pull the engine out of my '70 Plus 2. I have never
done this before so I am looking for some basic guidence. Here what I
have done so far - removed everything that needs to be removed except:
1. the clutch slave cylinder. Somehow, it's just fused to the clutch
housing. The circlip is off but it won't budge nor rotate. Even the
air hammer and chisel won't budge it. So I figure, since I am pulling
the engine only (leaving the transmission in place), I really don't
need to remove the clutch slave cylinder at this time. Is that correct
2. haven't separated the engine from the transmission since I assume I
need to support the engine before I do that.
Can I remove the engine on my own or do I need an assistant?
I have a cherry picker and a load balancer. I am wondering where to
screw the load balancer into the engine to attach it. I have heard of
people hanging a sling off the load balancer; is that a better way to go?
- elanplus2s130
- New-tral
- Posts: 9
- Joined: 22 Oct 2004
prasanthajayakody
I have always found it easier to remove the engine and gearbox as a
unit, do whatever work is required and replace it as a unit especially
if you have to do some work on the gearbox/clutch. It is much easier to
line up the gearbox and engine (spigot bearing) out of the car before
you put it back in. I have always slung the engine from the engine
mounts and under the rear of the sump with someone to help with
supporting the gearbox.
Others will probably disagree.
Rod
Rodney Stevens
CSIRO Minerals
phone 02 9710 6701
Mobile 0432 506 427
Web: http://www.minerals.csiro.au/
Personal Web Page
http://mywebpage.netscape.com/rodjohnst ... mepage.htm
-----Original Message-----
From: ***@***.***lto:***@***.***
Behalf Of prasanthajayakody
Sent: Wednesday, 2 August 2006 8:49 AM
To: ***@***.***
Subject: [LotusElan.net] engine removal help
Of course, the project is progressing much slower than expected but I
am finally ready to pull the engine out of my '70 Plus 2. I have never
done this before so I am looking for some basic guidence. Here what I
have done so far - removed everything that needs to be removed except:
1. the clutch slave cylinder. Somehow, it's just fused to the clutch
housing. The circlip is off but it won't budge nor rotate. Even the
air hammer and chisel won't budge it. So I figure, since I am pulling
the engine only (leaving the transmission in place), I really don't
need to remove the clutch slave cylinder at this time. Is that correct
2. haven't separated the engine from the transmission since I assume I
need to support the engine before I do that.
Can I remove the engine on my own or do I need an assistant?
I have a cherry picker and a load balancer. I am wondering where to
screw the load balancer into the engine to attach it. I have heard of
people hanging a sling off the load balancer; is that a better way to
go?
I have always found it easier to remove the engine and gearbox as a
unit, do whatever work is required and replace it as a unit especially
if you have to do some work on the gearbox/clutch. It is much easier to
line up the gearbox and engine (spigot bearing) out of the car before
you put it back in. I have always slung the engine from the engine
mounts and under the rear of the sump with someone to help with
supporting the gearbox.
Others will probably disagree.
Rod
Rodney Stevens
CSIRO Minerals
phone 02 9710 6701
Mobile 0432 506 427
Web: http://www.minerals.csiro.au/
Personal Web Page
http://mywebpage.netscape.com/rodjohnst ... mepage.htm
-----Original Message-----
From: ***@***.***lto:***@***.***
Behalf Of prasanthajayakody
Sent: Wednesday, 2 August 2006 8:49 AM
To: ***@***.***
Subject: [LotusElan.net] engine removal help
Of course, the project is progressing much slower than expected but I
am finally ready to pull the engine out of my '70 Plus 2. I have never
done this before so I am looking for some basic guidence. Here what I
have done so far - removed everything that needs to be removed except:
1. the clutch slave cylinder. Somehow, it's just fused to the clutch
housing. The circlip is off but it won't budge nor rotate. Even the
air hammer and chisel won't budge it. So I figure, since I am pulling
the engine only (leaving the transmission in place), I really don't
need to remove the clutch slave cylinder at this time. Is that correct
2. haven't separated the engine from the transmission since I assume I
need to support the engine before I do that.
Can I remove the engine on my own or do I need an assistant?
I have a cherry picker and a load balancer. I am wondering where to
screw the load balancer into the engine to attach it. I have heard of
people hanging a sling off the load balancer; is that a better way to
go?
- Guest
You can remove it by yourself, I have, and with the transmission. But it's
good to have someone just for safety sake. If for no other reason than
someone with clean hands to do the bbq and fetch an occaisional cool one.
Fred
On Tuesday 01 August 2006 5:48 pm, prasanthajayakody wrote:
good to have someone just for safety sake. If for no other reason than
someone with clean hands to do the bbq and fetch an occaisional cool one.
Fred
On Tuesday 01 August 2006 5:48 pm, prasanthajayakody wrote:
-
Fred Talmadge - Fourth Gear
- Posts: 666
- Joined: 24 Sep 2003
On the other hand, have a helper when reinstalling!
Ken
'69 Lotus Elan +2 with BDR
_____
From: ***@***.***lto:***@***.*** Behalf
Of Fred Talmadge
Sent: Wednesday, August 02, 2006 7:40 PM
To: ***@***.***
Subject: Re: [LotusElan.net] engine removal help
You can remove it by yourself, I have, and with the transmission. But it's
good to have someone just for safety sake. If for no other reason than
someone with clean hands to do the bbq and fetch an occaisional cool one.
Fred
On Tuesday 01 August 2006 5:48 pm, prasanthajayakody wrote:
Ken
'69 Lotus Elan +2 with BDR
_____
From: ***@***.***lto:***@***.*** Behalf
Of Fred Talmadge
Sent: Wednesday, August 02, 2006 7:40 PM
To: ***@***.***
Subject: Re: [LotusElan.net] engine removal help
You can remove it by yourself, I have, and with the transmission. But it's
good to have someone just for safety sake. If for no other reason than
someone with clean hands to do the bbq and fetch an occaisional cool one.
Fred
On Tuesday 01 August 2006 5:48 pm, prasanthajayakody wrote:
'69 Lotus Elan +2 with Cosworth BDR
'84 Ferrari 400i
'94 Subaru SVX
'04 Audi allroad
'84 Ferrari 400i
'94 Subaru SVX
'04 Audi allroad
- lotuselan2
- Fourth Gear
- Posts: 556
- Joined: 19 Oct 2005
4 posts
• Page 1 of 1
Total Online:
Users browsing this forum: No registered users and 24 guests