Refurb alloy wheels

PostPost by: friedy » Mon Jan 09, 2023 9:20 pm

My alloys are possibly original, well at least 30 years old but in good condition just needs repainting. I've spoken to one place and he won't do them as thinks might be too much magnesium in the ally which would become porous if acid dipped and powder coated. Wondering what the concensus is and others have done as don't want to risk messing them up.
Thanks
Alan.
Attachments
20230106_071617.jpg and
User avatar
friedy
Second Gear
Second Gear
 
Posts: 104
Joined: 06 Sep 2011

PostPost by: StressCraxx » Mon Jan 09, 2023 9:57 pm

Have you considered vapor blasting for paint removal? Then mask, repaint with a good quality wheel paint such as Wurth. Then polish the bare metal with alu polish.
There is no cure for Lotus, only treatment.
User avatar
StressCraxx
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1414
Joined: 26 Sep 2003

PostPost by: alan.barker » Tue Jan 10, 2023 5:50 am

+1 a good wheel paint and for me not powder epoxy.
When i did a set for a 1973 +2S130 for the part hidden under Tyre i used a paint for alloy radiators.

Sorry to say this but the Hub and Spinner are fitted on the wrong side. You have fitted righthand thread Spinner on the left side of your car. On the lefthand side it should be lefthand thread. the Hub should have red paint for left side and green for right side. On Lotus Elans and +2 Elans they are the opposite to Triumph, mgb or Jags.
Alan
Alan.b Brittany 1972 elan sprint fhc Lagoon Blue 0460E
alan.barker
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 3681
Joined: 06 Dec 2008

PostPost by: 111Robin » Tue Jan 10, 2023 9:50 am

Vapour blast then using a mini DA sander (I use an air DA with 2" pad) start with a 60 grit then work up to as high as you need to achieve the best possible finish. Then mask off the polished areas (time consuming but using a razor blade very easy to achieve perfect edges). Spray on a couple of coats of acid etch primer followed by a good quality paint. I have used VHT satin black wheel paint with good results. I have completed many sets of Dunlop D1 alloys using this method with very good results.
Attachments
Screenshot 2023-01-10 094821.jpg and
Screenshot 2023-01-10 094900.jpg and
111Robin
Third Gear
Third Gear
 
Posts: 270
Joined: 06 Feb 2021

PostPost by: friedy » Tue Jan 10, 2023 12:42 pm

This is what I expected, powdercoat is not the way to go.
Hi Alan, the photo is of the right hand rear wheel been like this for over 10 years and thread direction matches the front.
User avatar
friedy
Second Gear
Second Gear
 
Posts: 104
Joined: 06 Sep 2011

PostPost by: alan.barker » Tue Jan 10, 2023 1:05 pm

Sorry i thought it was the front wheel
Alan
Alan.b Brittany 1972 elan sprint fhc Lagoon Blue 0460E
alan.barker
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 3681
Joined: 06 Dec 2008

PostPost by: friedy » Tue Jan 10, 2023 5:54 pm

That's ok Alan, always a good idea to mention it if there's any doubts as we know what would happen if it was wrong :?
User avatar
friedy
Second Gear
Second Gear
 
Posts: 104
Joined: 06 Sep 2011

PostPost by: Spyder fan » Thu Jan 12, 2023 11:57 am

I used these people for my wheel refurb over 10 years ago https://www.lepsons.com/

Admittedly the wheels were more modern Minilite lookalikes, but the finish was and still is amazing. They will do painted, diamond cut, polished whatever you want, I'm sure with their experience they would do a good job no matter what the wheel.

four wheels will cost you about £500 including removing and refitting tyres
Kindest regards

Alan Thomas
User avatar
Spyder fan
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2843
Joined: 11 Jun 2009

PostPost by: evanlotus » Mon Jan 23, 2023 3:01 am

I had a set powder coated, blasted them then baked at 475 degrees to out gas them and then powder coated them. the mag will hold up just fine. I have done 3 sets of mageseum wheels with no problems.
evanlotus
First Gear
First Gear
 
Posts: 33
Joined: 02 Dec 2022

Total Online:

Users browsing this forum: No registered users and 16 guests