Page 1 of 1

gearbox snap ring.

PostPosted: Mon Jan 30, 2017 6:30 pm
by davidj
Good evening,

I am in the process of reassembling my gearbox and it is all going according to plan apart from a puzzle. I originally stripped it down 4 months when it would not engage reverse and discovered the remains of a rail sleeve restricting the reverse mechanism.

I have started putting is back together but have two 1 1/4 (approx) snap rings. One is used to hold the input bearing in place on the input shaft, but where does the second one go? I cannot see it on the manual illustration. Any suggestions? The big nut on the output shaft holds the first/second gears in place, while a much smaller snap ring holds third gear in place.

Thanks in advance for any help. I don't wish to progress any further in case I have missed something. It is a mystery!

Cheers,

David

Re: gearbox snap ring.

PostPosted: Mon Jan 30, 2017 7:19 pm
by KevJ+2
Hello David,
Someone on here called Gearbox (Alan) has posted about 6 videos on You Tube showing his 2000E box rebuild. Certainly worth a look.
Kev.

Re: gearbox snap ring.

PostPosted: Mon Jan 30, 2017 8:03 pm
by promotor
The snap ring should hold 1st/2nd synchroniser assembly onto the main shaft (if you have a mainshaft without the separate sleeve that first gear runs on).
It should be slightly thinner gauge than the one that holds the bearing on to the main drive.

HTH

Re: gearbox snap ring.

PostPosted: Mon Jan 30, 2017 8:04 pm
by AHM
Probably the one that holds the 3th/4th Synchro hub in place

Re: gearbox snap ring.

PostPosted: Mon Jan 30, 2017 8:55 pm
by davidj
HTH,

You may be onto something. I have been following the instructions/illustrations in the lotus manual, which show the early assembly, with the steel bush with the first gear (which I do not have) and no snapring. If there is a snapring on the first gear, I may have missed it, in which case, I will have to disassembly the mainshaft again. Drat! :-(

Thanks!

Re: gearbox snap ring.

PostPosted: Mon Jan 30, 2017 10:59 pm
by Craven
Hi,
I think the snap ring to which you refer is fitted to the mainshaft holding the 1st 2nd synchro hub in place, 1st gear is then fitted. Not shown in most, if not all, exploded views of the gearbox.
A lesson to those who believe the workshop manual has all the answers.
Ron.

Re: gearbox snap ring.

PostPosted: Wed Feb 01, 2017 12:42 pm
by davidj
HTH and Ron,

Thanks very much for your advice; yes, it was the snapring which holds the first/second syncro in place. It is not mentioned in the workshop manual, and a warning for anyone attempting the same exercise!

Cheers,

David

Re: gearbox snap ring.

PostPosted: Wed Feb 01, 2017 7:12 pm
by Sking06
The transmission does not like having that snap ring left out. Mine was and it didn't take long for the 1st gear to weld itself to the shaft.

Skip King
69 Elan S4

Re: gearbox snap ring.

PostPosted: Fri Feb 03, 2017 2:09 pm
by promotor
davidj wrote:HTH and Ron,

Thanks very much for your advice; yes, it was the snapring which holds the first/second syncro in place. It is not mentioned in the workshop manual, and a warning for anyone attempting the same exercise!

Cheers,

David


Glad you're sorted!

Re: gearbox snap ring.

PostPosted: Fri Feb 03, 2017 8:31 pm
by ElanDNA
davidj wrote:HTH and Ron,

Thanks very much for your advice; yes, it was the snapring which holds the first/second syncro in place. It is not mentioned in the workshop manual, and a warning for anyone attempting the same exercise!

Cheers,

David

Hello
I let the pictures speak

Re: gearbox snap ring.

PostPosted: Fri Feb 03, 2017 8:35 pm
by promotor
ElanDNA wrote:
davidj wrote:HTH and Ron,

Thanks very much for your advice; yes, it was the snapring which holds the first/second syncro in place. It is not mentioned in the workshop manual, and a warning for anyone attempting the same exercise!

Cheers,

David

Hello
I let the pictures speak


That's a useful break-down of parts but it's not relevant to the problem as that picture relates to 3rd/4th synchroniser and not 1st/2nd synchroniser!