Page 1 of 2

small or large front upright?

PostPosted: Thu Aug 09, 2007 12:51 am
by rdssdi
How can the various uprights and stub axles be identifdied?

How can the "larger" bearing (GT 6) upright be identified from the "smaller" bearing Spitfire front upright?

Bob
1969 Elan +2

Re: small or large front upright?

PostPosted: Thu Aug 09, 2007 1:12 am
by garyeanderson
Hi Bob
All knock on uprights used the larger GT6 uprights, stub shafts
Bolt on wheels used the early spitfire equivelents.
The stub axles are 5/8"and 1 inch in diameter on the spitfire/bolt-on hubs The stub axles are 3/4" and 1.060" on the GT6/knock-on

Gary

upright I.D.

PostPosted: Thu Aug 09, 2007 2:24 am
by rdssdi
What if a P.O. replaced a KO original upright with an earlier spitfire (bolt on) upright?

Would the hub fit onto the stub axle?

Could a larger (GT 6) stub axle fit onto a small bearing upright?

Bob

Re: small or large front upright?

PostPosted: Thu Aug 09, 2007 10:43 am
by garyeanderson
Hi Bob
Inner and out bearings are different as well as the Hubs (Elan and
Plus 2 knock-on hubs are also different),stub axles and uprights. It would be easier for a upright assembly to be swapped onto a bolt on wheel car than a knock-on wheel vehicle but that doesn't mean much to the average Lotus home/pro mechanic. If it can be done wrong, it may very well be done wrong...

Gary

upight

PostPosted: Thu Aug 09, 2007 3:06 pm
by rdssdi
Thanks Gary.

I have a Bean calalog. I will use it as a reference. I am now into front end alignment and wissh to cover all bases. Thanks again.

Bob

Re: small or large front upright?

PostPosted: Fri Sep 27, 2019 9:53 am
by billwill
Front Suspension 1967 S3 coupe

Can you visually tell the difference between an upright for a bolt-on axle from an upright for a knock-on axle if no axle is fitted?

I would hate to take mine apart, including removing the axles from the old uprights only to find that I had got the wrong new uprights.

Re: small or large front upright?

PostPosted: Fri Sep 27, 2019 10:51 am
by Craven
A good indicator but maybe not 100%, this cast in pip indicates a late casting that has the larger taper bore.
p1020878.jpg and

Re: small or large front upright?

PostPosted: Fri Sep 27, 2019 11:25 am
by Frogelan
It is possible to do the full GT6 conversion to bigger bolt on hubs / bearings / axles / uprights...I have done this (part by error, then by design).

I have just one suggestion: whilst this works for Girling AR calipers (alignment) i have not tried it with the original calipers...

Is it possible to spot...no, IMHO.

Re: small or large front upright?

PostPosted: Fri Sep 27, 2019 11:27 am
by vxah
The tapered stub axle hole is also smaller in the "bolt on" upright, if the two types were together you would see a visual difference.
My PO had fitted the wrong upright then by hand, ground down the taper to make the larger stub fit!

Re: small or large front upright?

PostPosted: Fri Sep 27, 2019 12:22 pm
by Craven
There are a number of aftermarket hangers available that allow a variety of caliper to fit this upright.
GT6 hanger = P16 Spitfire hanger = P14.

Re: small or large front upright?

PostPosted: Fri Sep 27, 2019 3:21 pm
by billwill
Can I tell by measuring the outside and inside diameters of the axle tapered hole with a digital caliper. If so does anyone know what the figures should be?

Re: small or large front upright?

PostPosted: Fri Sep 27, 2019 6:59 pm
by vxah
Outside stub hole measures about 27.5mm on the big upright and small upright is about 26mm.
Inner hole size is 21.5 for big upright and 20mm for smaller upright.

Re: small or large front upright?

PostPosted: Fri Sep 27, 2019 11:55 pm
by billwill
Thank you.

I will measure the pair (that I bought off a fellow member here) tomorrow, before I go ahead with ordering a new set of Trunnion bits from Sue Miller.

Re: small or large front upright?

PostPosted: Fri Sep 27, 2019 11:57 pm
by billwill
vxah wrote:Outside stub hole measures about 27.5mm on the big upright and small upright is about 26mm.
Inner hole size is 21.5 for big upright and 20mm for smaller upright.


Are these for bolt-on axle stubs or for knock-on axle stubs ?

Re: small or large front upright?

PostPosted: Sat Sep 28, 2019 8:39 am
by vxah
Knock on uses the big stub which needs a bigger hole in the upright.
Bolt on uses a smaller stub so the upright has a smaller hole for it to fit into.