Lotus Elan

701 engine block

PostPost by: BenMcCarthy » Thu Apr 20, 2006 9:48 am

Having had the misfortune three months ago of having had a conrod push a hole through the side of my block I am now in the market for a new block.

I understand that it is possible to obtain the following blocks:

701 'M'
701 'L'
701 standard as say for Ford Cortina

Does anyone have any commetns on the merits and demerits of using the above blocks for a rebuild?

Thank you :?
BenMcCarthy
First Gear
First Gear
 
Posts: 46
Joined: 20 Oct 2003

PostPost by: carrierdave » Thu Apr 20, 2006 10:37 am

Hi there - have a look at this.

http://www.lotus-cortina.com/library/block/blocks.htm

It doesn't cover the 701L block but gives you plenty of other suggestions.

regards

David
carrierdave
Third Gear
Third Gear
 
Posts: 326
Joined: 23 Sep 2004
Location: Rochester, Kent

PostPost by: tdafforn » Thu Apr 20, 2006 11:35 am

are you sure you don't mean 711m block?
these seem to be the ones to have!
Tim
User avatar
tdafforn
Fourth Gear
Fourth Gear
 
Posts: 744
Joined: 12 Sep 2003
Location: Kenilworth Warwks.

PostPost by: BenMcCarthy » Thu Apr 20, 2006 11:49 am

thanks for replies -
no its 701 M block

made in Germany I believe and somewhat beefier

For originality I would prefer a 701 block although its questionable what a 711 bottom end would take of the value of an Elan +2 - do you agree?
BenMcCarthy
First Gear
First Gear
 
Posts: 46
Joined: 20 Oct 2003

PostPost by: gjz30075 » Thu Apr 20, 2006 1:46 pm

Ben, I have the 711 bottom end (I presume you mean main caps and crank) and the torque increase feels great. There's more to it that just plopping in the crank and I'm not using a 701 block but well worth the upgrade and there was enough meat in the block to go to 84mm on the bore. I'm sure it'll add value to the car.
User avatar
gjz30075
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 3022
Joined: 12 Sep 2003
Location: Roswell, Georgia, USA

PostPost by: carrierdave » Thu Apr 20, 2006 2:51 pm

Obviously with the purist then matching chassis and engine numbers are crucial to selection of the right car.

However given the bigger capacity and more torque on the 711m block; you then have to look at driveability and enjoyment of the ride.

If I was looking to replace my block I would look for a 701M or 681F ?L? block to keep the car as authentic as possible. If I was purchasing a car, then one with a 711M block would not be discounted.

We are all aware that blocks are few and far between therefore compromises need to be made to keep the cars on the road.

Regards

David
carrierdave
Third Gear
Third Gear
 
Posts: 326
Joined: 23 Sep 2004
Location: Rochester, Kent

PostPost by: Dag-Henning » Thu Apr 20, 2006 6:54 pm

Pls don't forget that if you go for the 711-block ( 1600) you will have to use a longer timing-chaine, spacer for the front cover etc. The block is 1/2" taller that the 681 or 701.

Dag
Elan S1 -64/ Elan race-replica 26R / Works Escort TwinCam -69/ Brabham BT41 Holbay
User avatar
Dag-Henning
Third Gear
Third Gear
 
Posts: 330
Joined: 30 Sep 2004
Location: Oslo, Norway

Total Online:

Users browsing this forum: No registered users and 6 guests