Page 1 of 1

Cams , rods and crank

PostPosted: Fri Mar 09, 2012 10:26 pm
by Greg Foster
I have engine parts which may be of good use to someone.
1 set intake and exhaust cams reground by Chambers ---good
1 set of rods; 125 e -- good.
1 6 bolt crank turned 10 but will need turning again.
Parts were removed by Jim Justice Racing Engines in Frederick MD.
Make an offer for the parts you need.
Greg

Re: Cams , rods and crank

PostPosted: Sun Mar 11, 2012 11:10 am
by lotuselanman
Gidday,
Chambers reground cams !!
What are there specs and how much do you desire for them ?
Les.

Re: Cams , rods and crank

PostPosted: Tue Nov 19, 2013 10:33 pm
by zog
Hi,

Did you ever sell your engine parts? I just pulled an engine apart and found 3 166E rods and on 125E rod. I wouldn't mind upgrading the cams while I'm in there....

Thanks,

Bob Herzog
[email protected]

Re: Cams , rods and crank

PostPosted: Thu Nov 21, 2013 2:41 am
by nomad
What are 166e rod's? A set went begging on E-bay a while back and when I asked the same question here ie what are they, I got no answer. Newby here...are they a better rod than 125e?

Thanks
Kurt
26/3754

Re: Cams , rods and crank

PostPosted: Thu Nov 21, 2013 6:11 am
by types26/36
I don't know what 166 rods are but maybe it was a typo and should have said 116E which would have been the skinny early rods......just a thought :?:

Re: Cams , rods and crank

PostPosted: Thu Nov 21, 2013 7:11 pm
by nomad
OK.....makes sense....maybe the e-bay listing was wrong as well or my memory has gotten the better of me again.

Kurt
26/3754

Re: Cams , rods and crank

PostPosted: Thu Nov 21, 2013 7:21 pm
by types26/36
Here is a pic of 116E rods..... skinny compared with 125E.

Re: Cams , rods and crank

PostPosted: Fri Nov 22, 2013 1:00 pm
by lottex
Hi, I need a pair of cams for an S2 SE or something vaguely similar. However, I'm not an expert! But a similar pair sold for ?60 on ebay the other day-could 50 or 60 quid work for you? Obviousmy hoping that they might or might not be OK for the car. I could always get them reprofiled...
Thanks in advance
Peter

Re: Cams , rods and crank

PostPosted: Fri Nov 22, 2013 6:51 pm
by nomad
types26/36 wrote:Here is a pic of 116E rods..... skinny compared with 125E.


I have a set of the 116E rods out of my S1 but they are not nice and straight like those! A couple of mine have a definite bend in them.
Will be replaced by the 125E rods!

Kurt.

Re: Cams , rods and crank

PostPosted: Fri Nov 22, 2013 11:53 pm
by zog
FYI

166E rods are what you get when you fat finger 116E on the keyboard....

Sorry,

zog

Re: Cams , rods and crank

PostPosted: Sun Nov 24, 2013 1:07 pm
by Greg Foster
Rods and cams have gone, crank is still available.....along with an unbored cortina block.
Greg

Re: Cams , rods and crank

PostPosted: Sun Nov 24, 2013 11:28 pm
by gjz30075
pm sent

Greg Z

Re: Cams , rods and crank

PostPosted: Tue Nov 26, 2013 12:23 am
by Greg Foster
Whats a fair price for the crank?
Greg