LotusElan.net Unified Search
Search results for: servo in category "Mods"
31 results found.
2 pages of results.
Sorted by relevance / Sort by date
Is anyone running a Zetec car with Sierra brakes and no servo? I am looking at fitting dual line brakes but a dual servo is ...
... zetec brake servo Is anyone running a Zetec car with Sierra brakes and no servo? I am looking at fitting dual line brakes but a dual servo is ...
Dear All For a while I have been thinking of improving the brake set-up on my Plus2 , this has been brought about by my ...
... Plus2 servo replacement Dear All For a while I have been thinking of improving the brake set-up on my Plus2 , this has been brought about by my need ...
I should probably have my head examined but I've been thinking about replacing my S2 Elan calipers with 26R type calipers and associated equipment. Has ...
... the full route. My car is an S2 SE which came with a brake servo, which I removed. The potential increase clamping power and choice of brake ...
Just posted in things in common and identified my Master Cylinder as a Datsun dual master with a .75 bore. If I go with +2 ...
... this is agood combo, so I posted again. Tahoe Do you have a servo? If I remember correctly a servo assisted car has a .7 master cyl ...
I have been using some of my spare time making this kit together with Michael from Mio Engineering. We have made several different kits all ...
... , but otherwise exactly the same setup. The difference between the standard calipers with servo and the Willwood calipers without servo is like night and day. The best ...
Has anyone fitted a tandem master cylinder to a RHD +2? There's a Nissan Sunny (1200) part that seems to work on the standard Elan ...
... sure if its the right bore diameter thou. Which brings in a critical question servo assisted or not? If you have servos there lot of larger diameter master ...
Lovely car I’d put up with the tight engine bay as well
... zetec brake servo Lovely car I'd put up with the tight engine bay as well gav ...
Before I changed the rear calipers to Sierra sliders, I ran a tandem master cylinder (the one from London taxis) and a dual circuit servo. ...
... a tandem master cylinder (the one from London taxis) and a dual circuit servo. The front calipers are Caterham 4 pots (1 1/2 inch ...
I'm looking to fit a fully adjustable pedal box to my 26GTS Ankle injuries mean I have to get the pedal spacing just right for ...
... I would agree, excep: The S Series Elans use a single (without servo) .70" master for Type 14 front and original rear calipers. My ...
Hi folks, Hopefully someone on here knows the answer to this one.... I'm collecting parts for a +2 brake conversion for my S3 elan and ...
... system; no real engineering reason but as I get older I've started thinking about servo leaks and why a 12-14cwt car should need a servo anyway. My Elise ...
11. Has Anyone Done An AR, NR Caliper Or Other Brake Conversion? : Mods - Page 2 by LotusElan.net [Mods]
Bill, You can get the D14R's from Dave Bean (part number is on the caliper ) As far as I know the alloy versions of ...
... Astounding improvement and it fitted with no mods. I started with a single circuit servo, then decided to split the circuits front and rear and I got hold ...
Check list for using a Dunnell manifold 1) You have an MT75 gearbox with hydraulic clutch that has the starter fitted to the RH side ...
... the poor performance is down to the master cylinder diameter and the absence of a servo. Andy Widnall recently fitted a servo to his own car and says it ...
From what I remember from my research they are a standard Girling part but were used on very few vehicles, including a Morgan +4. No ...
... S2 Europa a smaller diameter, like ,7 or something and works well for servo less installs I have been running my + 2 Servo less for many years ...
Bob, To answer your question, the cv axles on my car are very similar to what Ray sells today, but are about 20 years old ...
... , high torque pre-engaged starter. Since I've owned it I got rid of the servo and put on a AP Racing tandem brake master cylinder, steel braided brake ...
I'm intrigued by the evaporator, for me that's the hardest part to fit, would you try to replace the heater unit? Given how standard the ...
... where I hung mine, I put the alternator below so I could preserve the servos gus gus wrote: I would say that compressor is too new a style ...
I've been on LotusElan.net for several months now seeking ideas and input as I try to finish a stalled S3 project. You can read more ...
... The GTS car has TTR solid shafts. Can't recall if the S3 has a servo. I'd bin it if it has. On the road car I run ...
Hi all, I can't find the particular post on this. I remember reading about someone who had fitted this to their plus two and also ...
... . The kit provide rod clamps and stuff; issue I had was getting the servo firmly mounted and adjusted. I never did fully figure out how exactly Spyder ...
18. Headlight vacuum fix : Mods by LotusElan.net [Mods]
When I had a problem with the headlight vacuum a while back, I made up these little locks from Builders Metal Strip. Avoided that dreaded ...
... run in conjunction with the manifold port like a lot of moderns do for brake servo easy to return to standard if needs be & they go up & down ...
19. erratic slow running : Mods by LotusElan.net [Mods]
Well here goes. You may not like this. My Elan runs rough when cold, but improves a lot once warmed up. If I bring it ...
... and drives well once up to normal temperature. So- I have fitted a servo motor to adjust the slow running speed! It consists of a chinese geared ...
Hi Mike, You have had exactly the same thought as me. I am currently restoring a 1973 +2, but when I have finished in a ...
... and electric ceramic heater on, together with an electric vacuum pump for the brake servo. Will be interested to see how you get on. Mark markcs I ...
Search took 0.090 seconds